Potassium Chloride Pure BP USP ACS FCC Food Grade Manufacturers

Anmol Chemicals is the pioneer manufacturers of Potassium Chloride, Pharmaceutical Excipients Fragrance & Flavor chemicals in India. We offer Halal and Kosher Potassium Chloride made in an ISO9001, ISO22000 (FSSC22000) and cGMP certified facility. Our group has several manufacturing facilities spread across the world, supported by toll manufacturers and representatives in UAE, Europe, Africa, USA, China and has several associated manufacturing facilities spread across India. All the Information on Physics, Chemistry, Applications, Uses and Technology on Manufacture of Potassium Chloride is in these pages.

The units have one or more of the certifications like FDA GMP, ISO 9001, ISO 22000, HACCP, REACH, Kosher & Halal

Potassium Chloride Manufacturers

Assay: Potassium Chloride contains not less than 99.0 percent and not more than 100.5 percent of KCl, calculated on the dried basis.
Identification: A solution (1 in 20) responds to the tests for Potassium and for Chloride.
Acidity or alkalinity: To a solution of 5.0 g in 50 mL of carbon dioxide–free water add 3 drops of phenolphthalein TS: no pink color is produced. Then add 0.30 mL of 0.020 N sodium hydroxide: a pink color is produced.
Loss on drying: Dry it at 105 for 2 hours: it loses not more than 1.0% of its weight.
Iodide or bromide:
IODIDE: To pass the test. The limit is 0.1%.
Aluminum: where it is labeled as intended for use in hem dialysis— Proceed as directed using 2.0 g of Potassium Chloride to prepare the Test Preparation: the limit is 1 µg per g.
Calcium and magnesium: To 20 mL of a solution (1 in 100) add 2 mL each of 6 N ammonium hydroxide, ammonium oxalate TS, and dibasic sodium phosphate TS: no turbidity is produced within 5 minutes.
Sodium: A solution (1 in 20), tested on a platinum wire, does not impart a pronounced yellow color to a non-luminous flame.
Heavy metals: Dissolve 2.0 g in 25 mL of water: the limit is 0.001%.
Organic volatile impurities: meets the requirements.

CHARACTERS
Appearance: White or almost white, crystalline powder or colorless crystals.
Solubility: Freely soluble in water, practically insoluble in anhydrous ethanol.

IDENTIFICATION
It gives the reactions of chlorides.
Solution S gives the reactions of potassium.

TESTS
Solution S: Dissolve 10.0 g in carbon dioxide-free water R prepared from distilled water R and dilute to 100 ml with the same solvent.
Appearance of solution: Solution S is clear and colorless.
Acidity or alkalinity: To 50 ml of solution S add 0.1 ml of bromothymol blue solution. Not more than 0.5 ml of 0.01 M hydrochloric acid or 0.01 M sodium hydroxide is required to change the color of the indicator.
Bromides: Maximum 0.1 per cent.
Iodides: Moisten 5 g by the drop wise addition of a freshly prepared mixture of 0.15 ml of sodium nitrite solution, 2 ml of 0.5 M sulphuric acid, 25 ml of iodide-free starch solution and 25 ml of water. After 5 min, examine in daylight. The substance shows no blue color.
Sulphates: Maximum 300 ppm.
Aluminium: Maximum 1.0 ppm, if intended for use in the manufacture of hem dialysis solutions.
Barium: To 5 ml of solution S add 5 ml of distilled water and 1 ml of dilute sulphuric acid. After 15 min, any opalescence in the solution is not more intense than that in a mixture of 5 ml of solution S and 6 ml of distilled water.
Iron: Maximum 20 ppm.
Magnesium and alkaline-earth metals: Maximum 200 ppm, calculated as Ca.
Sodium: Maximum 0.10 per cent, if intended for use in the manufacture of parenteral preparations or hem dialysis solutions.
Heavy metals: Maximum 10 ppm.
Loss on drying: Maximum 1.0 per cent, determined on 1.000 g by drying in an oven at 105 C for 3h.

DESCRIPTION: Potassium Chloride occurs as colorless, elongated, prismatic, or cubical crystals, or as a white, granular powder. It is stable in air. Its solutions are neutral to litmus. It may contain up to 1.0% (total) of suitable food-grade ant-caking, free-flowing, or conditioning agents such as calcium stearate or silicon dioxide, either singly or in combination. One gram dissolves in 2.8 mL of water at 25°, and in about 2 mL of boiling water. Potassium Chloride containing anti-caking, free-flowing, or conditioning agents may produce cloudy solutions or dissolve incompletely. It is insoluble in alcohol.
Function: Nutrient; gelling agent; salt substitute; yeast food.

REQUIREMENTS:
Identification: A 1:20 aqueous solution gives positive tests for Potassium and for Chloride.
Assay: Not less than 99.0% of KCl after drying; and not less than 98.0% of KCl after drying when a sample contains added substance.
Acidity or Alkalinity: A sample containing no added substance passes test.
Heavy Metals (as Pb): Not more than 5 mg/kg.
Iodide and/or Bromide: Passes test.
Loss on Drying: Not more than 1.0%.
Sodium: Passes test.

We also offer free flowing Anti caking Potassium Chloride with suitable anti caking agent.

Potassium Chloride Analytical Reagent ACS Specifications
Potassium Chloride KCl
Formula Wt 74.55
CAS Number 7447-40-7

REQUIREMENTS
Assay: 99.0-100.5% KCl
pH of a 5% solution: 5.4-8.6 at 25C
MAXIMUM ALLOWABLE
Insoluble matter: 0.005%
Iodide (I): 0.002%
Bromide (Br): 0.01%
Chlorate and nitrate (as NO3): 0.003%
Nitrogen compounds (as N) 0.001%
Phosphate (PO4): 5 ppm
Sulfate (SO4): 0.001%
Barium (Ba): Passes test
Heavy metals (as Pb): 5 ppm
Iron (Fe): 3 ppm
Calcium (Ca): 0.002%
Magnesium (Mg): 0.001%
Sodium (Na): 0.005%

Exports to USA, Canada, UAE, Dubai, South Africa, Tanzania, Kenya, Nigeria, Egypt, Uganda, Turkey, Mexico, Brazil, Chile, Argentina, Europe Netherlands, Italy, Spain, Germany, Portugal, France, Malaysia, Indonesia, Thailand, Korea, Vietnam, Japan, etc.

Potassium Chloride BP IP FCC USP Food Grade manufacturers at:

Anmol Chemicals
S-8, SARIFA MANSION, 2ND FLANK ROAD, CHINCHBUNDER, MUMBAI 400009, INDIA
TEL: (OFFICE) 91-22-23770100, 23726950, 23774610, 23723564. FAX: 91-22-23728264

Specification	Our Guaranteed
Percent by wt.	99% (KCl) Potassium Chloride
Iron	10 ppm
Sodium Chloride	1%
Matter insoluble in water	0.05%
Sulphate	0.05%
Heavy metals as Lead	5 ppm
Hydroxides	.01%
Calcium	0.02%
Magnesium	0.05%
Moisture % by Wt. Max.	1%